|
Under the Whyte notation for the classification of steam locomotives, 4-2-0 represents the wheel arrangement of four leading wheels on two axles, two powered and coupled driving wheels on one axle, and no trailing wheels. This type of locomotive, often called a Jervis type, was common on American railroads from the 1830s through the 1850s. Other equivalent classifications are: UIC classification: 2′A (also known as German classification and Italian classification) French classification: 210 Turkish classification: 13 Swiss classification: 1/3 ==History== The first 4-2-0 built was the ''Experiment'' (later named ''Brother Jonathan'') for the Mohawk and Hudson Railroad in 1832. It was built by the West Point Foundry based on a design by John B. Jervis. Having little else to reference, the manufacturers patterned the boiler and valve gears after locomotives built by Robert Stephenson of England. In England, it had developed from the 2-2-2 design of Stephenson's first Long Boiler locomotive, around 1840, which he had altered to place two pairs of wheels at the front with the outside cylinders between them to improve stability. A few examples of Stephenson locomotives were already in operation in America, so engineers did not have to travel too far to get their initial ideas. In America, the design was a modification of the 0-4-0 design then in common use. The 0-4-0 proved to be too rigid for the railroads of the day, often derailing on the tight curves and quick elevation changes of American railroads. For the 4-2-0, Jervis introduced a four-wheel leading truck under the locomotive's smokebox that swiveled independently from the main frame of the locomotive (in contrast to the English engines mentioned earlier, which had rigid frames). The pistons powered a single driving axle at the rear of the locomotive, just behind the firebox. This design resulted in a much more stable locomotive that was able to guide itself into curves more easily than the 0-4-0. This design proved so effective on American railroads that many of the early 0-4-0s were rebuilt as 4-2-0s. The 4-2-0 excelled in its ability to stay on the track, especially those with single driving axles behind the firebox, whose main virtue was stability. But, with only one driving axle behind the smokebox, the locomotive's weight was spread over a small proportion of powered wheels, which meant its total power was substantially reduced. However, other 4-2-0 locomotives had the driving axle in front of the firebox, adhesive weight was increased. One possible solution was one patented in 1834 by E. L. Miller and used extensively by Matthias W. Baldwin, in which raising a pair of levers attached the tender frame to an extension of the locomotive frame, transferring some weight from the tender to the locomotive frame, making more weight available for adhesion. However, an automatic version was patented in 1835 by and George E. Sellers and used extensively by Norris after he obtained rights to it. This system used a beam whose fulcrum was the driving axle. On flat and level surfaces, the beam was slightly raised. But at starting or on grades, the resistance made the beam assume a horizontal position, which caused the locomotive to tip upward. This plan placed more of the locomotive's weight on the driving axle, but by reducing the weight on the leading truck, also made it more prone to derailments A more practical solution, first put into production by Norris, moved the driving axle to a location on the frame in front of the locomotive's firebox. This was done because Baldwin refused to grant rights to Norris to use his patented "half-crank" arrangement. Cantilevering the weight of the firebox and the locomotive crew behind the driving axle placed more weight on the driving axle without substantially reducing the weight on the leading truck. However, Norris's design led to a shorter wheelbase, which tended to offset any gains in the tractive force on the driving axle by reducing the locomotive's overall stability. A number of Norris locomotives were imported into England for use on the Birmingham and Bristol Railway since, because of the Lickey Incline, British manufacturers declined to supply. As the 1840s approached, and more American railroads were experimenting with the new 4-4-0 locomotive type, the 4-2-0 fell out of favor as it was not as able to pull a paying load on the railroad as the 4-4-0. 4-2-0s were built into the 1850s, but their use was restricted to light-duty trains as most railroads by this time had found them unsuitable for regular work. In England, for freight work, four-coupled and six-coupled engines were performing well. However, for passenger work, the aim was greater speed. Because of the fragility of cast-iron connecting rods, "singles" continued to be used, with the largest driving wheels possible. For some reason, British manufacturers did not take up the idea of mounting the forward wheels on a bogie for some years. Possibly there were fears about their stability, but with a long rigid frame, greater speed was achieved at the cost of a very rough ride and damage to the track. The culmination of this approach was seen in the Crampton locomotive where, to make the drivers as large as possible, they were mounted behind the firebox. Once steel became available, greater rotational speeds became possible with multiple, smaller coupled wheels. 抄文引用元・出典: フリー百科事典『 ウィキペディア（Wikipedia）』 ■ウィキペディアで「4-2-0」の詳細全文を読む スポンサード リンク
|