| 翻訳と辞書 |
6V6
The 6V6 is a beam-power tetrode, introduced as the 6V6G by Ken-Rad Tube & Lamp Corporation in late 1936,〔http://www.americanradiohistory.com/Archive-Radio-Engineering/30s/1936/Radio-Engineering-1936-12.pdf〕 it is still in use in audio applications, especially electric guitar amplifiers. Following the introduction in July 1936 of the 6L6, the potential of the scaled down version that became the 6V6 was soon realized. The lower-powered 6V6 was better suited for average home use, and became common in the audio output stages of "farmhouse" table-top radios, where power pentodes such as the 6F6 had previously been used. The 6V6 required less heater power and produced less distortion than the 6F6, while yielding higher output in both single-ended and push-pull configurations. Although the 6V6 was originally designed especially for use in automobile radios,〔http://www.americanradiohistory.com/Archive-Radio-Today/30s/Radio-Today-1936-12.pdf〕 the clip-in Loctal base 7C5,〔http://frank.pocnet.net/sheets/201/7/7C5.pdf〕 from early 1939, or the lower heater current 12V6GT, both with the identical characteristics to the 6V6, but with the smaller T-9 glass envelope, soon became the tubes of choice for many automotive radios manufacturers. Additionally, the 6V6 had applications the portable radio market.
The data sheet information supplied by the tube manufacturers design centers, list the typical operation of an audio output stage for a single 6V6 as producing about 5W of continuous power, and a push-pull pair about 14W. Amplifier manufacturers soon realized that the tube was capable of being used at ratings above the recommended maximums, and guitar amplifiers with 400V on the plates of a pair of 6V6GTA claim to produce an output power of 20W RMS at 5%THD with 40W Peak Music Power, and with 490V on the plates, as much as 30W RMS.
==History==
Following the 6V6G, RMA Release #96 – 09 Nov. 1936, sponsored by Ken-Rad Tube & Lamp Corporation, with the ST shouldered glass envelope, the 6V6 was announced with a metal mantel in January 1937 by Hygrade Sylvania.〔http://www.americanradiohistory.com/Archive-Radio-Today/30s/Radio-Today-1937-01.pdf〕 The RMA Release #125 – 03 Jan.1938, Sponsored by RCA. for the 6V6 tube has led to some confusion as to the origins of the 6V6. The 6V6G but not the 6V6 is in the RCA manual RC-13 from July 1937. Tube manufacturers were promoting the superiority of metal tube designs in the second half of the 1930s, and this tube, having been introduced during that period, was produced in large quantities in this format. The introduction of the 6V6GT, RMA Release #201 – 10 July 1939, was sponsored by Hytron Corporation. By 1940, the 6V6 was mostly being produced in this smaller "GT" T-9 glass envelope.〔http://frank.pocnet.net/sheets/049/6/6V6.pdf〕 The 6V6GTA – RMA Release #1681 – 2 July 1956, sponsored by Hygrade Sylvania Corporation, has a controlled warm-up period.〔http://frank.pocnet.net/sheets/049/6/6V6GTA.pdf〕
抄文引用元・出典: フリー百科事典『 ウィキペディア（Wikipedia）』
■ウィキペディアで「6V6」の詳細全文を読む
スポンサード リンク
| 翻訳と辞書 : 翻訳のためのインターネットリソース |
Copyright(C) kotoba.ne.jp 1997-2016. All Rights Reserved.
|
|