|
The GWR 4100 Class was a class of steam locomotives in the Great Western Railway (GWR) of the United Kingdom. The Badminton class express passenger 4-4-0 steam locomotives were introduced in 1897 as a development from the earlier Duke class. The name Badminton was chosen after the Duke of Beaufort's Badminton estate, through which the GWR was building a new line to South Wales at the time. Further modifications to the design resulted in the Atbara Class entering service in 1900, the names for these locomotives generally being taken from contemporary military engagements or senior army commanders. Later engines were named after cities of the British Empire. The final batch of locomotives were named after varieties of garden plant and in consequence were known as the Flower Class. These three types were later standardised and treated as a single class, so are listed together here. Four other prototype 4-4-0s, originally built in 1894 as the Armstrong Class, were also later rebuilt as Badmintons (see below). This class were subject to the 1912 renumbering of GWR 4-4-0 locomotives, which saw the Bulldog Class gathered together in the series 3300-3455, and other types renumbered out of that series. This class took numbers 4100-4172 (of which numbers 4101-4120 had previously been used by Flower Class locomotives). ==Badminton class== The first member of the class, no. 3292, was completed in December 1897 with a domed parallel boiler, a raised Belpaire firebox and an extended, built-up smokebox similar to that used on the Duke Class. The outside frames were curved over each driving wheel axle. It was named ''Badminton'' in April 1898. A batch of eleven locomotives, nos. 3293 to 3303, were completed between April and July 1898, with a further batch of eight, nos. 3304 to 3311, between September 1898 and January 1899. The class were the first locomotives on the GWR to be fitted with copper Belpaire fireboxes. The penultimate example, no. 3310 ''Waterford'', was fitted with a domeless parallel boiler, a steel Belpaire firebox, and an enlarged cab.〔〔 The class were fitted with a steam chest and slide valves located beneath the cylinders. The valves were driven by Stephenson valve gear. This inverted arrangement of slide valves and steam chest, originally introduced by William Stroudley of the LSBCR, allowed the valves to drop away from the cylinder's steam port faces when the regulator was closed, thus reducing wear. Because the steam chest was below the cylinders, and not between them, the latter could have an increased diameter. The centre line of the cylinders was inclined at an angle of 6° to the centre line of the valves, each centre line being aligned with the driving centre. This arrangement allowed the valve rods to be driven directly from the expansion link.〔 First used on the Armstrong and 3031 Classes, this arrangement of cylinders, valves and valve gear was subsequently used on all GWR outside framed 4-4-0s, with the slide valves being eventually replaced by piston valves. The crankpins for the coupling rods were placed in line with the corresponding inside crankpins for the connecting rods.〔〔 This arrangement was also developed by Stroudley, who claimed that the motion of the inside cranks was smoothly transferred to the coupling rods, as happens in an outside-cylindered engine, where the connecting rod acts directly on a crankpin shared with the coupling rod. According to Stroudley, the axleboxes, bearing surfaces, hornblocks and coupling rods of locomotives with outside cylinders had a service life twice as long as those on inside-cylindered examples. However, by aligning the two cranks together, heavy balancing weights were required on the driving wheels, at 180° to the outside crank, to counteract the combined mass of the cranks and rods.〔 The Badmintons had massive crescent-shaped balancing weights, which made the unmounted pairs of wheels difficult to handle in the workshop.〔 One locomotive of the Badminton Class was rebuilt with an experimental boiler. With the impending opening of the direct Reading-Taunton route which was of more undulating nature than the route via Bristol, there was a need to ensure that the most appropriate locomotives were provided. Churchward's Chief Assistant, F.G. Wright, designed a large boiler with a very deep firebox, which was fitted to no. 3297 ''Earl Cawdor'' in July 1903. The boiler was designed to hold a large volume of hot water, forming a reservoir to assist the locomotive running along an undulating line. It also provided a steam space of as against the of the Standard No. 4 boiler, the larger of the two types of standard boiler fitted to the 4-4-0s. This increase in volume was intended to provide a reservoir of steam.〔 The firebox was set deep between the coupled axles, with a horizontal grate.〔 The intention with this was to allow a thick fire to be built up, increasing the area of the firebox in contact with the fire, and decreasing the temperature gradient along the firebox plates, thus reducing the risk of broken firebox stays.〔 The boiler was pressed to .〔 No. 3297 was also fitted with a large cab with two side windows, reminiscent of North Eastern practice.〔 The locomotive was regularly rostered on the most demanding trains, but it soon became apparent that it was not up to the work demanded and it was relegated to secondary duties. In October 1906 the boiler was removed and replaced by a Standard No.4 boiler, the North Eastern style side-window cab having been replaced by a Churchward type in November 1904.〔 抄文引用元・出典: フリー百科事典『 ウィキペディア（Wikipedia）』 ■ウィキペディアで「GWR 4100 Class」の詳細全文を読む スポンサード リンク
|