|
The HKS-1 was a German 19 span high performance two seat sailplane, designed around 1950 to use recent advances in laminar flow airfoils. To avoid premature transition from laminar flow caused by surface interruptions, the HKS-1 dispensed with hinged ailerons, flaps and spoilers and replaced them with a flexible trailing edge. Two were built, setting several records. ==Design and development== Any aerodynamic approach that decreased wing drag was welcomed by sailplane designers, who reduced lift-induced drag with high aspect ratio wings. Profile drag was reduced by maintaining laminar flow over as much of the wing as possible.〔 The NACA 6-series profiles of the late 1930s suggested that laminar flow might be maintained as far back as 70% chord, though military experience during World War II showed that much less ambitious targets were hard to achieve with riveted surfaces on wings with gaps for control surfaces, armament, service hatches etc. After the war, sailplane designers realised that their wooden surfaces could, with care, be made smoother over long distances than metal ones, that sailplanes had fewer wing surface interruptions than military machines and their lower speeds meant lower Reynolds numbers, encouraging stronger laminar flow. Such aircraft began to appear from 1950 onwards and showed striking improvements in performance. The HKS-1 was a tandem two seat sailplane first flown in 1953, designed to be fast but also to fly slowly for soaring in thermals. Its designers chose a 14% maximum thickness to chord ratio NACA airfoil, capable of maintaining laminar flow over the front 50% of the wing at lift coefficients between 0.5 and 0.9. They noted that the first of the laminar designs, the Ross-Johnson RJ-5, only achieved its potential after its flaps and spoilers were removed and the underside aileron hinge gaps carefully sealed, so decided to remove all hinged control surfaces and replaced them by wing warping. To do this, the trailing edge had to be flexible and controllable from wing root to tip.〔 The HKS-1 was a wooden aircraft, largely covered with a plywood/rigid plastic foam/plywood sandwich skin (PFP). The wings had strong spruce and ply double box spars; major ribs were made from PFP and were assisted by intermediate foam ribs. The first two layers of the sandwich skin were added from the leading edge to an auxiliary spar at 70% chord and precisely shaped. The outer plywood sheet of the PFP sandwich was then wrapped continuously around and glued to the inner layers, leaving no gaps. Final external shaping reduced the waviness to 50 μm. Before this outer layer was attached, the area of it corresponding to the last 30% of chord, where it formed the whole skin thicknees, was weakened by cuts through its inner plies, making it flexible enough to warp when driven by internal parallelogram frames opened and closed by lateral control rods. The edges could be warped differentially to act as ailerons or together to change camber. Control loads were reported as heavy.〔 The wing was mid-mounted with some dihedral and also with forward sweep to improve the visibility from the tandem cockpit. The fuselage was PFP skinned over PFP frames, with a shaped balsa outer layer for smoothness. This proved to be too easily damaged and was replaced on the second aircraft with a glass-fibre shell. The HKS-1 had a fully retractable monowheel undercarriage, assisted by partially retractable nose-skid/nose-wheel combination. In the absence of airbrakes it used a tail ribbon parachute. It had a 100° V-tail of similar construction to the wings.〔 The HKS-1 made its first flight at Düsseldorf in July 1953. Early tests showed that it was tail heavy, so 10 kg (22 lb) of water ballast was added in the nose. Speeds were high and the glide ratio 38:1. With two pilots aboard, the wing loading of 35 kg/m² (7.2 lb/sq ft) was high for the time and limited the minimum turn radius, so other slower gliders could better exploit narrow thermals. It was this observation which led to the development of the HKS-3, a smaller single seat sailplane with a lower wing loading and other changes but similar in design to the HSK-1.〔 In 1955 a second example, the HKS-1 ''V2'' flew. This was identical to the HKS-1 apart from a 3° decrease in forward sweep, made to compensate for the tail heaviness, and replacement of the vulnerable balsa fuselage sheath with fibre-glass.〔 This second machine is called the HKS-2 by some authors,〔 whereas others associate this name with a development abandoned during its design stage.〔 抄文引用元・出典: フリー百科事典『 ウィキペディア（Wikipedia）』 ■ウィキペディアで「HKS-1」の詳細全文を読む スポンサード リンク
|