|
In aviation, a localizer (LOC) is the lateral component of the instrument landing system (ILS) for the runway centreline when combined with the vertical glide slope, not to be confused with a locator, although both are parts of aviation navigation systems. A localizer (like a glideslope) works as a ''cooperation'' between the transmitting airport runway and the receiving cockpit instruments. An older aircraft without ILS receiver cannot take advantage of any ILS facilities at any runway, and much more important, the most modern aircraft have no use of their ILS instruments at runways which lack ILS facilities. In parts of Africa and Asia large airports may lack any kind of transmitting ILS system. Some runways have ILS only in one direction, this can however still be used (with a lower precision) known as ''back beam''. ==Localizer in cockpit== In modern cockpits, the localizer is seen as a colored dot (usually in the shape of a diamond) at the bottom of the artificial horizon gauge. It does not appear during cruise, but comes up during the descent and approach to the selected runway, provided that the navigation radio is set to the ILS frequency of that specific runway. If the transmitted localizer beam, which usually, but not always, is directed in the heading of the runway extension. (exceptions exist f.i. in Innsbruck, Austria and in Macao, China) If the aircraft is located on this line, the localizer dot will appear in the middle of the scale. But if the aircraft is located a little ''left'' of the beam, the marker will appear to the ''right'' on the localizer gauge scale in cockpit. The pilot then knows he or she must adjust the heading ''towards'' the dot. In older cockpits, the localizer scale below the artificial horizon is rather short. But in older style cockpit instrumentation, the localizer also appears as an arrow in the gyro compass below the artificial horizon. The top and bottom of this arrow "is one unit", which shows current heading. But the middle part of this arrow is moving independently of the aircraft's heading. The middle of that arrow could be described as being "stand alone", and moves to the left if the aircraft is located to the right of localizer beam and to the right if the aircraft is located to the left of the localizer beam. When the arrow is "united" to a straight line, then the aircraft is following the localizer beam. (This second "arrow-indicator" is omitted in modern cockpits, but the main compass is still located below the artificial horizon) At previously mentioned exceptions of runways, where the ILS beam is not leading all the way to the runway, the runway needs to be visible before the final approach begins. The very first generation of localizer gauges had a different cockpit interface, and were not included in the artificial horizon nor any compass, but at a gauge of its own. The localizer was then represented as a dangling stick hanging from a fixed point at the top of a separate gauge, and the glideslope was represented by a similar, but horizontal, dangling stick, fixed at one of the sides of the gauge. When the aircraft was located exactly at the ILS-beam (or glidepath) the two sticks formed a cross. This interface resembles the fllight director, which also forms a cross, but on the artificial horizon. This older ILS instrumentation system was omitted around the same time as jet airliners like Boeing 707 and DC 8 were introduced. The expression "Catch the localizer" refers to runway approaches with the autopilot on. The angle between the aircraft heading and localizer beam should be less than 30 degrees, and the indicated airspeed at least below 250 knots (for jet airliners), then by pushing a button marked "APP" or "ILS", then the autopilot presumably will turn and then follow the localizer. The autopilot will then also automatically descend according to the glideslope. Normal procedure is to catch the localizer first and then follow the glideslope as well. If the angle is too large or the airspeed too high, catching the localizer might fail. Modern aircraft can land "themselves", provided the runway ILS is of sufficient standard (class III C) and the cross wind component is low. Pure autolandings are mostly done in foggy weather. The cockpit ILS gauges is not to be confused with the flight director, which also is located on the artificial horizon gauge. A flight director only shows how the autopilot would fly. If the localizer dot (or arrow) indicate runway is to be found to the left, but the flight director suggests a right turn, and the runway isn't visible, then the pilot in command is having difficulties. Some runways have ILS beams intended for use in one direction only. However, as the localizer beam by its nature also goes backwards, it can still be of some use. This is called ''back beam''. It's of help during the approach, but the use of back beam localizer gives less precision compared to normal use. 抄文引用元・出典: フリー百科事典『 ウィキペディア（Wikipedia）』 ■ウィキペディアで「Localizer」の詳細全文を読む スポンサード リンク
|