翻訳と辞書
Words near each other
・ Valérie Bonnier
・ Valérie Boyer
・ Valérie Bègue
・ Valérie Bénaïm
・ Valérie Courtois
・ Valérie Crouzet
・ Valérie Crunchant
・ Valérie Damidot
・ Valve Anti-Cheat
・ Valve audio amplifier
・ Valve audio amplifier technical specification
・ Valve Corporation
・ Valve cover racing
・ Valve exerciser
・ Valve float
Valve gear
・ Valve guide
・ Valve hall
・ Valve job
・ Valve leakage
・ Valve microphone
・ Valve No. 10
・ Valve of coronary sinus
・ Valve of inferior vena cava
・ Valve oil
・ Valve Pormeister
・ Valve Records
・ Valve replacement
・ Valve RF amplifier
・ Valve seat


Dictionary Lists
翻訳と辞書 辞書検索 [ 開発暫定版 ]
スポンサード リンク

Valve gear : ウィキペディア英語版
Valve gear

The valve gear of a steam engine is the mechanism that operates the inlet and exhaust valves to admit steam into the cylinder and allow exhaust steam to escape, respectively, at the correct points in the cycle. It can also serve as a reversing gear. It is sometimes referred to as the "motion".
==Purpose==

In the simple case, this can be a relatively simple task as in the internal combustion engine in which the valves always open and close at the same points. This is not the ideal arrangement for a steam engine, though, because greatest power is achieved by keeping the inlet valve open throughout the power stroke (thus having full boiler pressure, minus transmission losses, against the piston throughout the stroke) while peak efficiency is achieved by only having the inlet valve open for a short time and then letting the steam expand in the cylinder (expansive working).
The point at which steam stops being admitted to the cylinder is known as the ''cutoff'' and the optimal position for this varies depending on the work being done and the tradeoff desired between power and efficiency. Steam engines are fitted with regulators (throttles in US parlance) to vary the restriction on steam flow, but controlling the power via the cutoff setting is generally preferable since it makes for more efficient use of boiler steam.
A further benefit may be obtained by admitting the steam to the cylinder slightly before front or back dead centre. This advanced admission (also known as ''lead steam'') assists in cushioning the inertia of the motion at high speed.
In the internal combustion engine, this task is performed by cams on a camshaft driving poppet valves, but this arrangement is not commonly used with steam engines, partly because achieving variable engine timing using cams is complicated. Instead, a system of eccentrics, cranks and levers is generally used to control a D slide valve or piston valve from the motion. Generally, two simple harmonic motions with different fixed phase angles are added in varying proportions to provide an output motion that is variable in phase and amplitude. A variety of such mechanisms have been devised over the years, with varying success.
Both slide and piston valves have the limitation that intake and exhaust events are fixed in relation to each other and cannot be independently optimised. Lap is provided on steam edges of the valve, so that although the valve stroke reduces as cutoff is advanced, the valve is always fully opened to exhaust. However, as cutoff is shortened, the exhaust events also advance. The exhaust release point occurs earlier in the power stroke and compression earlier in the exhaust stroke. Early release wastes some energy in the steam, and early closure also wastes energy in compressing an otherwise unnecessarily large quantity of steam. Another effect of early cutoff is that the valve is moving quite slowly at the cutoff point, and this causes 'wire drawing' of the steam, another wasteful thermodynamic effect visible on an indicator diagram.
These inefficiencies drove the widespread experimentation in poppet valve gears for locomotives. Intake and exhaust poppet valves could be moved and controlled independently of each other, allowing for better control of the cycle. In the end, not a great number of locomotives were fitted with poppet valves, but they were common in steam cars and lorries, for example virtually all Sentinel lorries, locomotives and railcars used poppet valves. A very late British design, the SR Leader class, used sleeve valves adapted from internal combustion engines, but this class was not a success.
In stationary steam engines, traction engines and marine engine practice, the shortcomings of valves and valve gears were among the factors that lead to compound expansion. In stationary engines trip valves were also extensively used.

抄文引用元・出典: フリー百科事典『 ウィキペディア(Wikipedia)
ウィキペディアで「Valve gear」の詳細全文を読む



スポンサード リンク
翻訳と辞書 : 翻訳のためのインターネットリソース

Copyright(C) kotoba.ne.jp 1997-2016. All Rights Reserved.